We offer four commercial roof repair services in Hastings, each matched to the roof system on your building and the place water gets in.
Our Services
These commercial roof repair services in Hastings cover membrane roofs, metal roofs, active leaks, and plant roofs.
TPO, EPDM, PVC, built-up, and modified bitumen roofs get matched patches, seam repairs, drain flashing, and ponding fixes. A moisture check of the board below comes first, so a patch never seals wet insulation under new membrane.
See flat roof repair
Exposed-fastener and standing-seam roofs get new screws and washers, resealed end laps, refastened ridge caps, and rusted panels swapped for the same profile and gauge. Light panels and curb flashing on metal roofs fall here too.
See metal roof repair
Stains and drips get traced with meters, core cuts, infrared, or water tests, and the failed seam, curb, drain, or fastener gets repaired. Equipment and wall leaks that only look like roof leaks get ruled out early.
See leak repair
Plants and large warehouses get exhaust fan, curb, and stack repairs in materials picked for the exposure. Work follows plant safety rules and gets scheduled around shifts, breaks, and planned shutdowns.
See industrial roof repairService Fit
Start with the roof you have and the problem you see on it. This table points to the service that usually fits that pair.
| Service | Roof Types | Common Problems | Start Here When |
|---|---|---|---|
| Flat Roof Repair | Single-ply TPO, EPDM, and PVC, built-up, modified bitumen | Open seams, ponding at drains, blisters, punctures, cracked base flashing | The roof is low-slope and you can see the damage from the roof hatch |
| Commercial Metal Roof Repair | Exposed-fastener and standing-seam panels on shops and warehouses | Loose screws, cracked washers, rusted end laps, loose ridge caps, brittle light panels | Drips line up under purlins or panels show rust at the laps |
| Commercial Roof Leak Repair | Any commercial roof, membrane or metal | Stains with no clear source, leaks only in storms, water near rooftop units | You see water inside but cannot find the opening above |
| Industrial Roof Repair | Plant and large warehouse roofs of any system | Exhaust-softened membrane, curb cracks, clogged drains, worn service paths | Fans, stacks, or process residue sit on the roof around the leak |
You do not need to know the service name to call. Tell us where the water shows up, what sits under it, and what the roof is made of if you know, and we will sort out the rest.
Call UsRust, open seams, or ponding you want looked at? Schedule an inspection, and the repair list will say which service applies.
Schedule Free InspectionShared Process
All four services follow the same five decisions, from the first walk to the written close-out.
Every repair starts with a walk of the field, seams, drains, flashing, and curbs, plus a look inside for stains and wet tile. Moisture readings and core cuts show the wet board the eye misses.
Before any material comes out, the failed detail gets named: a lap, a washer, a drain clamping ring, a curb flashing. That name decides which service applies and which repair goes on the list, ranked by how much water it lets in.
Local damage on a firm roof is repair work. Wet board or brittle membrane across most of the roof gets an honest call that replacement is the better spend, along with a list of leaks worth stopping until that happens.
Patches match the membrane on the roof, fasteners match the panel and the size of the old holes, and flashing near exhaust fans matches what comes out of the stack.
Opened roof areas get closed before work stops for the day. The close-out notes list each failure, each repair, the materials used, and photos of both, so your file shows exactly what changed on the roof.
Question about your own roof?
Describe the roof and the problem, and we will tell you which service applies.
Call UsService Questions
It depends on the roof type and where water is getting in. Flat roof repair covers membrane and built-up roofs, metal roof repair covers panels, fasteners, and laps, leak repair finds and fixes active leaks, and industrial roof repair handles plants and large warehouses with heavy equipment.
Yes. Many buildings mix a metal shop with a low-slope office wing, or have a leak that turns out to be a curb on a plant roof. The inspection covers the whole roof, and the repair list groups the work however it falls.
Our work is repair. When the inspection shows that most of the roof is wet or brittle, we say so in writing so you can plan a replacement with the right roofer, and we can still stop active leaks in the meantime.
Usually. Most repairs happen from the roof side while work goes on below. Areas under the repair get protected, and noisy or messy work over sales floors or production lines gets scheduled around hours or shutdowns.
Some repairs do, and the scope decides it. Nebraska's state building code adopts the 2018 International Existing Building Code, which covers repairs in Chapter 4. The City of Hastings lists a separate roofing permit application, and Development Services confirms whether a given repair needs one.
Most single-detail repairs, such as a seam patch, a curb reflash, or a row of fasteners, take part of a day once the materials are on site. Section repairs with wet insulation take longer, and weather decides when adhesives and tapes can go down.
A written close-out with what failed on the roof, what was repaired, the materials used, and photos before and after. Those notes make the next inspection faster and give you a record for insurers, lenders, or buyers.
Send the address and a note on what you see, inside or on the roof. We will inspect it, name what failed, and tell you in writing which repairs it needs and in what order.
